Base
N3662822026-11-06NY

RE: The classification and country of origin of a chemical injector kit for a pressure washer

U.S. Customs and Border Protection · CROSS Database · 1 HTS code referenced

Summary

RE: The classification and country of origin of a chemical injector kit for a pressure washer

Ruling Text

U.S. Department of Homeland Security U.S. Customs and Border Protection National Commodity Specialist Division One World Trade Center, Suite 51.201 New York, NY 10007 U.S. Customs and Border Protection N366282 November 6, 2026 CLA-2-84:OT:RR:NC:N1:102 CATEGORY: Classification; Origin TARIFF NO.: 8481.80.9015 Sarah Li Autowin Group Limited Flat/RM 08, 15/F Witty Commercial Building 1A-1L Tung Choi Street Mongkok, Kowloon, Hong Kong China RE: The classification and country of origin of a chemical injector kit for a pressure washer Dear Ms. Li: In your letter dated October 22, 2026, you requested a classification and country of origin ruling on a chemical injector kit. Descriptive literature was provided for our review. The product under consideration is described as a chemical injector kit for high-pressure washers (SKU W03K2), which is a retail-packaged downstream injection system that completes the activity of introducing cleaning chemicals into the water stream after being released from a pump. The kit consists of 16 feet of PVC tubing, a regulating valve of brass material, a quick plug, a brass fitting, a black nozzle tip, a filter, and PTFE thread seal tape, packaged together ready for retail sale. In operation, the regulating valve, which is designed to control the flow of chemicals and liquids received from the tubing connected to a pump, functions as a pressure actuating suction valve. The rigid, non-movable brass fitting features a through-hole that transmits this negative pressure to guide the liquid without telescopic movement or retraction. The quick plug enables tool-free connection and disconnection from the high-pressure washer’s water outlet. The black nozzle tip, which features a fixed orifice, is designed to accelerate the mixed fluid of water and foam concentrate, entraining air to produce and project foam from the outlet. Additionally, a filter attached to the suction hose inlet screens out impurities to protect the control valve and nozzle from clogs, while the included PTFE thread seal tape is applied to threaded connections to provide a seal across both high-pressure water paths and suction circuits. In your letter, you suggest the kit is classified within subheading 8424.90.9080, Harmonized Tariff Schedule of the United States (HTSUS), which provides for Mechanical appliances (whether or not hand operated) for projecting, dispersing or spraying liquids or powders; fire extinguishers, whether or not charged; spray guns and similar appliances; steam or sand blasting machines and similar jet projecting machines; parts thereof: Parts: Other: Other. We disagree. The kit constitutes goods classified in two or more headings, which are put up in a set ready for retail sale. Goods that are, prima facie, classifiable under two or more headings, are classifiable in accordance with General Rule of Interpretation (GRI) 3, HTSUS. GRI 3(a) states in part, when two or more headings each refer to part only of the materials or substances contained in mixed or composite goods, those headings are to be regarded as equally specific, even if one heading gives a more precise description of the good. Goods classifiable under GRI 3(b) are classified as if they consisted of the material or component which gives them their essential character, which may be determined by the nature of the material or component, its bulk, quantity, weight or value, or by the role of a constituent material in relation to the use of the article. In this instance, this office finds that based on value and role, the regulating valve imparts the essential character of the kit. The regulating valve, which is the highest valued item in the kit, opens and closes to introduce cleaning chemicals and liquids, which is the intended activity of the kit. Valves and similar appliances are specifically provided for within heading 8481. Therefore, in accordance with GRI 3(b), the applicable subheading for the chemical injector kit will be 8481.80.9015, HTSUS, which provides for Taps, cocks, valves and similar appliances, for pipes, boiler shells, tanks, vats or the like, including pressure-reducing valves and thermostatically controlled valves; parts thereof: Other appliances: Other: Regulator valves, self-operating, for controlling variables such as temperature, pressure, flow and liquid level. The general rate of duty is 2 percent ad valorem. With respect to origin of the valve, which as mentioned above imparts the essential character of the kit, the assembly process begins by installing a screw from Malaysia into a valve body from Malaysia. Afterwards, a pressure adjusting spring from China and a lock nut are installed onto the outlet stem. Next, the lock nut and a conical spring from China are installed into a connector from Malaysia. The resulting connector assembly is installed into the valve body. Lastly, the finished valve is assembled to the other components packaged in the kit to complete testing and inspections. Once all testing and inspections are completed, the components are disassembled and the regulator valve is packaged with the remainder of the items, which include the Chinese items: PVC tubing, a filter, thread seal tape and a quick plug. When determining the country of origin for purposes of applying current trade remedies under Section 301 and additional duties, the substantial transformation analysis is applicable. See, e.g., Headquarters Ruling Letter H301619, dated November 6, 2018. The test for determining whether a substantial transformation will occur is whether an article emerges from a process with a new name, character, or use different from that possessed by the article prior to processing. See Texas Instruments Inc. v. United States, 681 F.2d 778 (C.C.P.A. 1982). This determination is based on the totality of the evidence. See National Hand Tool Corp. v. United States, 16 C.I.T. 308 (1992), aff’d, 989 F.2d 1201 (Fed. Cir. 1993). Additionally, Section 304 of the Tariff Act of 1930, as amended (19 U.S.C. 1304), provides that unless excepted, every article of foreign origin imported into the United States shall be marked in a conspicuous place as legibly, indelibly, and permanently as the nature of the article (or its container) will permit, in such a manner as to indicate to the ultimate purchaser in the United States, the English name of the country of origin of the article. Congressional intent in enacting 19 U.S.C. 1304 was “that the ultimate purchaser should be able to know by an inspection of the marking on the imported goods the country of which the goods is the product. The evident purpose is to mark the goods so that at the time of purchase the ultimate purchaser may, by knowing where the goods were produced, be able to buy or refuse to buy them, if such marking should influence his will.” See United States v. Friedlaender & Co., 27 C.C.P.A. 297, 302 (1940). Part 134 of the U.S. Customs and Border Protection (CBP) Regulations (19 CFR 134) implements the country of origin marking requirements and exceptions of 19 U.S.C. 1304. Section 134.1(b), CBP Regulations (19 CFR 134.1(b)), defines “country of origin” as the country of manufacture, production, or growth of any article of foreign origin entering the United States. Further work or material added to an article in another country must effect a substantial transformation in order to render such other country the “country of origin” within the meaning of the marking laws and regulations. Here, components from China and Malaysia are assembled into a valve body from Malaysia to produce a regulating valve, which imparts the essential character of the chemical injector kit. When determining the country of origin of valves, CBP has relied on the origin of the valve body, the essential component of a valve, as the process of assembling a valve is rather simple. Parts are typically assembled into a valve body by inserting, pressing, and screwing them to each other. See New York Rulings N339513 (dated May 6, 2024), N338713 (dated April 3, 2024), and N325765 (dated May 26, 2022). In this instance, the origin of the valve body is Malaysia. Therefore, as the origin of the valve is Malaysia, the origin of the chemical injector kit is Malaysia. The principles governing the country of origin marking of sets, mixtures, and composite goods, were addressed by CBP in Treasury Decision 91-7. In this decision, CBP determined in relevant part that for purposes of 19 U.S.C. § 1304, the relevant inquiry is whether the materials or components have been substantially transformed as a result of their inclusion in a set, mixture, or composite good. If the materials or components have not been substantially transformed, each component must be individually marked to indicate its own country of origin. If the marking would not be visible through the retail packaging, then the retail packaging must be marked to identify the origin of these articles. In this case, the PVC tubing, filter, thread seal tape and quick plug, although packaged and classified together as a set, do not lose their separate identities. Therefore, for marking purposes under 19 U.S.C. § 1304, these items must be marked to identify their individual countries of origin. The holding set forth above applies only to the specific factual situation and merchandise description as identified in the ruling request. This position is clearly set forth in Title 19, Code of Federal Regulations (CFR), Section 177.9(b)(1). This section states that a ruling letter is issued on the assumption that all of the information furnished in the ruling letter, whether directly, by reference, or by implication, is accurate and complete in every material respect. In the event that the facts are modified in any way, or if the goods do not conform to these facts at time of importation, you should bring this to the attention of U.S. Customs and Border Protection (CBP) and submit a request for a new ruling in accordance with 19 CFR 177.2. Additionally, we note that the material facts described in the foregoing ruling may be subject to periodic verification by CBP. The duties cited above are current as of this ruling’s issuance. Duty rates are provided for your convenience and are subject to change. The text of the most recent HTSUS and the accompanying duty rates are provided at https://hts.usitc.gov/. This ruling does not address the applicability of any additional duties, taxes, fees, exactions and/or other charges, which may apply to the goods discussed herein. This includes, but is not limited to, tariffs and other duties as provided for in Subchapter III to Chapter 99, HTSUS. Thus, for example, in addition to the classification stated above, the merchandise covered by this ruling may also need to be reported with either the Chapter 99 provision under which an additional tariff applies or one of the Chapter 99 provisions covering exceptions to such tariffs. For further information to assist with the importation process, please refer to the frequently updated Cargo Systems Messaging Service (CSMS) messages at https://www.cbp.gov/trade/automated/cargo-systems-messaging-service and the Trade Remedies page at https://www.cbp.gov/trade/programs-administration/trade-remedies. This ruling is being issued under the provisions of Part 177 of the Customs and Border Protection Regulations (19 C.F.R. 177). A copy of the ruling or the control number indicated above should be provided with the entry documents filed at the time this merchandise is imported. If you have any questions regarding the ruling, please contact National Import Specialist Sandra Martinez at sandra.martinez@cbp.dhs.gov. Sincerely, (for) James P. Forkan Director National Commodity Specialist Division