U.S. Customs and Border Protection · CROSS Database · 1 HTS code referenced
RE: The tariff classification of spool valve components from South Korea
U.S. Department of Homeland Security U.S. Customs and Border Protection National Commodity Specialist Division One World Trade Center, Suite 51.201 New York, NY 10007 U.S. Customs and Border Protection N365740 October 29, 2026 CLA-2-84:OT:RR:NC:N1:102 CATEGORY: Classification TARIFF NO.: 8481.90.9040 Minsu Jang Hyundai Transys 11, Dongtan-daero 24-gil Hwaseong-si Gyeonggi-do South Korea RE: The tariff classification of spool valve components from South Korea Dear Mr. Jang: In your letter dated October 5, 2026, you requested a tariff classification ruling. The five items in question are referred to as transmission spool valve components. The specifically configured components are engineered to be inserted into dedicated bores and passages of a valve body where they interface with additional components to complete a hydraulic valve that controls the flow of pressurized fluid. Each component contributes to the function of regulating pressure and changing the flow path of hydraulic fluid within a valve body. The valve-reducing, available as part number 46272-4G100 and 46272-T87800, is an aluminum alloy rod that features a tapered end that engages with a spring. The other end has a prominent cylindrical collar, while the midsection has a cylindrical body positioned closer to the tapered end. The rod weighs approximately 4.66 grams. The sleeve-switch, LR, part number 46274-2F600, is a steel rod with a weighted design on both ends. The ends are cylindrically shaped. An additional weighted design sits in the middle of the rod. The switch, which is designed to engage with a spring, weighs approximately 5.1 grams. The valve-switch, LR, part number 46303-4G200, is an aluminum alloy rod with a tapered end and a cylindrical collar at the other end. The midsection has two additional cylindrical bodies, which are close in proximity, and one positioned on the tapered end. The rod engages with a spring, interfaces with part number 46274-2F600, and weighs approximately 4.84 grams. The valve pressure control, T/C, part number 46312-4G100, is an aluminum alloy rod with a grooved tapered end and a cylindrical collar at the other end. The midsection has an additional cylindrical body positioned on the grooved tapered end. The rod interfaces with part number 46363-2F100 and weighs approximately 4.75 grams. The applicable subheading for the five spool valve components will be 8481.90.9040, Harmonized Tariff Schedule of the United States (HTSUS), which provides for Taps, cocks, valves and similar appliances, for pipes, boiler shells, tanks, vats or the like, including pressure-reducing valves and thermostatically controlled valves; parts thereof: Parts: Other: Of valves of subheading 8481.20: Other. The general rate of duty will be Free. The duties cited above are current as of this ruling’s issuance. Duty rates are provided for your convenience and are subject to change. The text of the most recent HTSUS and the accompanying duty rates are provided at https://hts.usitc.gov/. This ruling does not address the applicability of any additional duties, taxes, fees, exactions and/or other charges, which may apply to the goods discussed herein. This includes, but is not limited to, tariffs and other duties as provided for in Subchapter III to Chapter 99, HTSUS. Thus, for example, in addition to the classification stated above, the merchandise covered by this ruling may also need to be reported with either the Chapter 99 provision under which an additional tariff applies or one of the Chapter 99 provisions covering exceptions to such tariffs. For further information to assist with the importation process, please refer to the frequently updated Cargo Systems Messaging Service (CSMS) messages at https://www.cbp.gov/trade/automated/cargo-systems-messaging-service and the Trade Remedies page at https://www.cbp.gov/trade/programs-administration/trade-remedies. The holding set forth above applies only to the specific factual situation and merchandise description as identified in the ruling request. This position is clearly set forth in Title 19, Code of Federal Regulations (CFR), Section 177.9(b)(1). This section states that a ruling letter is issued on the assumption that all of the information furnished in the ruling letter, whether directly, by reference, or by implication, is accurate and complete in every material respect. In the event that the facts are modified in any way, or if the goods do not conform to these facts at time of importation, you should bring this to the attention of U.S. Customs and Border Protection (CBP) and submit a request for a new ruling in accordance with 19 CFR 177.2. Additionally, we note that the material facts described in the foregoing ruling may be subject to periodic verification by CBP. This ruling is being issued under the provisions of Part 177 of the Customs and Border Protection Regulations (19 C.F.R. 177). A copy of the ruling or the control number indicated above should be provided with the entry documents filed at the time this merchandise is imported. If you have any questions regarding the ruling, please contact National Import Specialist Sandra Martinez at sandra.martinez@cbp.dhs.gov. Sincerely, (for) James P. Forkan Director National Commodity Specialist Division